How to replace toto toilet seat with hidden bolts

Check the alignment of the seat and lid. Make sure they are centered and sit evenly on the toilet bowl. If needed, loosen the nuts slightly and adjust the position of the seat and lid accordingly. If your toilet seat has adjustable hinges, you can fine-tune the angle of the seat to achieve the desired position.

Follow these steps to remove this seat. Remove the plastic caps covering the bolts with a flathead screwdriver. Engage the head of the bolt with the screwdriver and reach for the wingnut under the bowl with your hand. Unscrew the bolt with the screwdriver as you hold the wing nut.Step 4: Install the Toilet Tank. Lift off the toilet tank and guide the bolts through the toilet bowl mounting holes until it's sitting pretty on top of the bowl. Put a rubber washer followed by a metal one and a nut on each bolt and hand tighten them. Use an adjustable wrench to tighten the bolts alternatingly.The Fix-it Guy demonstrates the installation of a washlét bidet toilet seat. This toilet seat model is a TOTO SW3036.Video Chapters0:0 Introduction0:30 Packa...Keeping the sleeve in place under the toilet will be necessary if the bolt twists with it. Attach locking pliers to the black sleeve that runs 2 inches under the bowl. Continue to tighten the screw until you can no longer spin the sleeve with the pliers handle in line with the porcelain bowl. The screw will thereafter be easy to remove.Top Mount Toilet Seat Hardware Replacement Toilet Seat Mounting Bolts For Toto Toilets - Compare to TOTO THU651N - Gateway Brand (Pack of 2) 4.6 out of 5 stars. 45. 200+ bought in past month. $9.99 $ 9. 99. ... Toilet seat Bolts Screws Replacement for Fixing The Top Toilet Seat, Toilet Seat Parts Including Screw and Nut for Top Mount Toilet ...To replace a Toto toilet seat with hidden bolts, follow these steps: 1. The first step is to locate the bolts securing the toilet seat. Depending on the model, these bolts may be hidden beneath caps or covers on the seat hinges. To access the bolts, gently pry open the caps with a screwdriver or your fingernail.Oct 27, 2021 · Toto Toilet Seat Removal. The following is the correct procedure to replace the Toto toilet seat: Identify and locate the seat bolt covers. Using a flat-head screwdriver, or just your hands, pry the side that is opposite the hinge to snap the cover-up and expose the bolt. Each one of the two covers hides the seat bolts at the back of the toilet ...

Step 1: Wipe Down the Toilet Seat. First, use a damp cloth to wipe down the toilet seat. This will remove any loose dirt or debris. Step 2: Use a Toilet Brush to Scrub the Seat. Next, use a toilet brush to scrub the toilet seat. Be sure to scrub around the hinges and the areas where the seat meets the bowl.See full list on bathroomer.orgTank to Bowl Toilet Kit: http://amzn.to/2mj9irLThe dreaded slow drip from a toilet bolt... We will show you how to fix a leaky toilet by replacing the hardwa...How to Replace a Toilet Seat with Hidden Bolts. Replacing a toilet seat with hidden bolts is a relatively simple task that can be completed in a few minutes. 1. Gather the necessary tools and materials. New toilet seat; Phillips head screwdriver; Flathead screwdriver; Pliers; Penetrating oil; Rag; 2. Turn off the water supply to the toilet. 3.I too have a Toto toilet and I was having trouble accessing the bottom of 1 side and the other side was impossible to access. I was able to loosen the screws enough and use a bolt cutter to pop off the heads of the screws. The rubber then was easy to push through. I reinstalled with the new TOTO rubber Mollys and it was an easy fix.1. Remove the two bolts that secure the toilet seat to the bowl. 2. Lift the seat off of the bowl. 3. Clean the bowl thoroughly. 4. Place the new seat on the bowl, making sure that the bolts are in the same holes as the old seat. 5. Tighten the bolts to secure the seat in place. How do you tighten a toilet seat with no access underside?To measure the toilet seat hinges, you will need to use a ruler. The first step is to measure from the top of the seat to where it meets the tank. This should be done with your ruler and pencil. The second step is to put down your measuring tape and look at both sides of the toilet seat hinge. Now, add those two measurements together for an ...

Hibbent Universal Toilet Seats Screws and Bolts Metal - Toilet Seat Hinges Bolt Screws, Toilet Seat Fixings Expanding Rubber,Toilet Seat Replacement Parts Kit(5 Choices) 4.3 out of 5 stars 1,141 1 offer from $15.99Apr 20, 2020 · Step 1: Turn off the Water on the Toilet. Locate the toilet shut-off valve on the rear wall of the toilet and turn it clockwise. If you have the push/pull type of valve, pull the handle out. Flush the toilet and hold the flush handle down to remove as much water as possible.The tank to bowl kit can break down, causing leaks. Repair the tank to bowl kit with the help of this free video presented by a professional and experienced ...The toilet seat itself, pushing down on the bolts day after day, can also fatigue and deform the plastic over the years. It's just a perfect storm of the plastic material, the bathroom environment, overtightening, and repetitive mechanical stress that eventually renders those bolts stuck in place.To attach a Toto toilet seat to a skirted toilet, you will need to use the special bolts and washers that come with the seat. First, remove the old seat and bolts from the toilet. Next, clean the surface of the toilet where the seat will be attached. Then, place the new seat on the toilet and align the holes with the bolts.Check the alignment of the seat and lid. Make sure they are centered and sit evenly on the toilet bowl. If needed, loosen the nuts slightly and adjust the position of the seat and lid accordingly. If your toilet seat has adjustable hinges, you can fine-tune the angle of the seat to achieve the desired position.

Taryn asher weight loss.

Step 1. Put on your hand gloves for protection and clean the toilet seat before working on it. Step 2. You can now secure the toilet seat with the duct or masking tape. This step is necessary since removing the hidden fixings can jostle or push against the toilet seat.American Standard toilet seats provide you with plenty of conveniences, from slow-closing lids to a special hinge locking system to keep the seat in place. But how do you remove a toilet seat with hidden bolts? Here's our list of tips and tricks to get the job done. Replacing an American Standard Toilet Seat With Hidden BoltsUnlike regular toilet seats that have visible bolts, Toto toilet seats have a unique design that requires a different approach. However, with the right tools and techniques, you can easily replace your Toto toilet seat with hidden bolts. In this article, we will guide you through the process step-by-step. Step 1: Gather the necessary tools ...Your donations help me to keep helping you .....https://www.paypal.com/donate?hosted_button_id=M3JK8MDR9NYB8#DIY #howto #billshowtoThis video demonstrates how to remove metal toilet seat anchors from your KOHLER toilet and replace them with repair kit 1461673. Replacing the metal anchors...

SoftClose Toilet Seat . View all filters. Filters. Type. Activating the following elements will cause content on the page to be updated. Filters ... We welcome your feedback about the TOTO website. Please fill in your contact information, below, and send us a note. We look forward to hearing from you.With the appropriate size, the toilet seat bolts are 2.6 inches in length, 1.1 inches in diameter of the washers, fitting well for most toilet seats. The toilet seat screws and bolts are made of quality plastic, solid, durable, anti-rust and anti-corrosion, hard to break and deform.Toilet seat bolts are the fixtures that hold the seat in place. These bolts are attached to the toilet bowl and secured with nuts. There are different types of toilet seat bolts, such as top-mount bolts and bottom-mount bolts. Installation and replacement of seat bolts can be done with basic tools like a wrench or pliers. When replacing a ...Ensure that the rubber washer is placed between the bottom of the inner tank and the bolt head. After inserting the bolts into the tank, place them in the pan and then into the toilet bowl openings. Tighten the bolts using your hands and then use a wrench to tighten them at the bottom of the toilet seat.1. Turn off the water supply to the toilet. Locate the water supply valve under the sink or behind the toilet. Turn the valve clockwise to turn off the water. 2. Flush the toilet to drain the water from the tank. 3. Remove the old toilet seat. There are two hidden bolts located on either side of the toilet bowl.Steps for choosing a toilet seat. Start by measuring the length of the toilet seat. They come as either round seats at 16″ or elongated at 18″. Be sure to buy the correct size seat. Unscrew the bolts at the back of the toilet seat holding it in place and remove the old toilet seat. Depending on how old the toilet seat is, this may require a ...This video demonstrates how to remove metal toilet seat anchors from your KOHLER toilet and replace them with repair kit 1461673. Replacing the metal anchors...1. Start by unscrewing the two bolts that hold the seat in place. These are usually located at the back of the seat. 2. Once the bolts are removed, lift the seat straight up and off of the toilet bowl. 3. Take the seat to your sink and clean it with warm, soapy water and a soft cloth or sponge.Step 2: Apply lubricant to the stripped bolt. Applying a high-quality penetrating lubricant is a crucial initial step in the process of removing a stripped toilet seat bolt. The lubricant works to penetrate the corroded or stuck threads of the bolt, effectively loosening its grip and facilitating easier removal.Oct 27, 2021 · Toto Toilet Seat Removal. The following is the correct procedure to replace the Toto toilet seat: Identify and locate the seat bolt covers. Using a flat-head screwdriver, or just your hands, pry the side that is opposite the hinge to snap the cover-up and expose the bolt. Each one of the two covers hides the seat bolts at the back of the toilet ...Simple, step by step tutorial on how to change a toilet seat and lid.

Attach the New Seat to the Toilet. Extract the current seat by unscrewing its nuts and bolts. Place and tighten the new seat on the toilet bowl. Adjust it until it is tight on the rim. Keep the old bolts and nuts (from the previous seat) in a safe place. You can use them to replace lost ones on the new toilet seat.

If you’re considering replacing or upgrading your toilet seat, it’s important to know the correct measurements to ensure a perfect fit. Measuring your toilet seat may seem like a s...Jan 11, 2024 · 1. Place the new toilet seat on the toilet bowl. 2. Insert the bolts through the holes in the toilet seat and into the nuts below the bowl. 3. Tighten the nuts with the adjustable wrench. 4. Replace the plastic caps over the bolts. You have now successfully removed and replaced an American Standard toilet seat with hidden bolts.Top Mount Toilet Seat Hardware Replacement Toilet Seat Mounting Bolts For Toto Toilets - Compare to TOTO THU651N - Gateway Brand (Pack of 2) 4.6 out of 5 stars. 50. ... 3 Inches Standard Stainless Steel Toilet Seat Bolts Replacement Kit Bathroom Toilet Repair Screw Kit. 4.5 out of 5 stars. 111. 100+ bought in past month. $9.99 $ 9. 99. FREE ...Step 4: Remove the Screws. Once the seat is gone, you'll have enough room to cut the screws out. In my case, I griped the head and started gently rocking it back/fwd, all the while spraying. You're in good shape if little pieces of anchor metal starts coming apart.Hey home pros! I just moved into a new apartment and I'm trying to install a simple bidet on my toilet. For the life of me, I cannot lift the tabs on this Toto toilet seat. The little cutouts are SO small that I keep chipping the plastic with any tool I've tried (needle nose pliers, a fork, my finger nail, paperclip, etc.).Replace & Fasten the New Toilet Seat. Position the new seat on top of the toilet bowl. Place the new seat bolts in the mounting holes, alight the seat, and attach the nuts. Using a screwdriver on the top, and the adjustable wrench on the bottom, tighten the seat bolts firmly. Now snap closed the bolt caps!In this video I demonstrate How To Remove & Replace a Plastic Soft Close Toilet Seat quickly and easily. This Toilet seat has a quick release feature so that...Mar 9, 2023 · Yes, you can put a Kohler toilet seat on a Toto toilet. The two brands are compatible with each other and there should be no problem putting the seat on the toilet. Begin by removing the old toilet seat from the toilet. If there are any screws holding it in place, remove them with a screwdriver. Next, clean the area around the toilet bowl where ...For this reason, we will have to remove the toilet seat first before we can remove the screws that hold it to the toilet. The first step is to wear gloves as toilet seats can be quite dirty. Open up the toilet seat completely (so both parts). If your toilet seat has a hidden fixing, you can often press the sides of the toilet seat.Put the toilet seat back on the toilet bowl. Align the holes in the seat's hinges with the begs on the toilet bowl. Set the seat back on the hinge pegs in the upright position. [7] If the hinges have a locking mechanism, make sure you push the seat all the way onto the pegs until the hinges snap into place. Method 2.

Breezynews kosciusko.

Crime watch lancaster.

1. REMOVE THE OLD TOILET SEAT. Make sure to clean the surface around the mounting holes. 2. INSTALL THE WASHLET SEAT MOUNTING BRACKET. Using a Phillips-head screwdriver, tighten the screws just snug enough to allow movement so you can adjust it to align the seat. 3. SLIDE THE WASHLET ON THE BRACKET.Easy Steps, Tips, Warnings & Items Needed To Replace Toilet Seat With Hidden Bolts If you want to replace toilet seat with hidden bolts then you need to gather all the required items and follow the steps for this process. Here are the list of required items and steps for this process. Also, go through the tips and warnings:Step 4: Tighten the Nuts Equally. Turn each bolt one-quarter turn to gradually tighten. Alternate tightening first one bolt, then the other. Beginning with the first side, tighten the nut as far as you can by hand. Then, use your wrench to make a quarter turn to the bolt. Repeat this process for the second side.There are two standard sizes of toilet seats in the United States. They are elongated and round. Elongated toilet seats are 18.5 inches long and round toilet seats are 16.5 inches long. To find out what kind of toilet seat you need, measure from the end of the bowl to the middle of the seat post holes. If this all sounds like jargon, don't worry.4 days ago · Attach the new toilet seat. Now, you should be free to mount the new seat. Match up the bolts with the holes and tighten the nuts. Be careful here not to over-tighten as you may want to remove the seat again someday. Check the lid and seat don’t wobble around when in any position, up or down, and adjust as necessary.Barney Bouy. 1.2K subscribers. How to fix a loose toilet seat with hidden bikes. This is a square push button flush toilet seat with soft closing lid. Takes no more than 5 minutes. All...Gotcha. I understand now. First, let's start with the replacement. Toto realized they made toilet seats that were ridiculously hard to replace, so they designed new expansion-type bolts that can be installed entirely from above--no need to hold a nut underneath.Step 2: Remove the old toilet seat. To remove the old toilet seat, follow these steps: 1. Locate the hinge caps: Look for two plastic caps covering the bolts at the back of the toilet seat. These caps are usually located near the toilet tank and may have the Kohler logo or “H” and “C” markings for hot and cold. 2. ….

In this video, I replace the toilet tank to bow bolts, and the tank to bowl gasket, to fix a slow water leak between the tank and the bowl. This fix is fast,...Jul 23, 2023 · To replace a TOTO toilet seat with hidden bolts, follow these steps: Locate the release buttons or access points on the seat hinges. Press or release the buttons to detach the seat from the mounting bolts. Remove the old seat and align the new seat’s holes with the mounting bolts.The third outlet is a ½" pipe thread that is compatible with most bidet seat hoses. If by chance your bathroom has a ½" shut-off valve, you will need our ½" t-valve instead. Simply install the skirted t-valve between your current toilet supply hose and the shut off valve on the wall. However, please be aware that the skirted t-valve is ...If you’re in need of a replacement truck seat, you may be concerned about the cost. However, with a little bit of knowledge and some smart shopping, you can save money on your purc...I too have a Toto toilet and I was having trouble accessing the bottom of 1 side and the other side was impossible to access. I was able to loosen the screws enough and use a bolt cutter to pop off the heads of the screws. The rubber then was easy to push through. I reinstalled with the new TOTO rubber Mollys and it was an easy fix.Top Mount Toilet Seat Hardware Replacement Toilet Seat Mounting Bolts For Toto Toilets - Compare to TOTO THU651N - Gateway Brand (Pack of 2) 4.6 out of 5 stars. 50. ... 2pcs Toilet Seat Screws Replacement Bolts, 3 Inches Standard Stainless Steel Toilet Seat Bolts Replacement Kit Bathroom Toilet Repair Screw Kit. 4.5 out of 5 stars. 111. 100 ...Nov 16, 2021 · About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features NFL Sunday Ticket Press Copyright ...Aug 30, 2022 · 3. Tighten the Toilet Lid. Once both lids have been popped open, you should see a plastic screw with a slit across the head. Find a flat-head screwdriver if you didn't use one to pry open the lids, and insert the head into the screw notch. Then look under your toilet on the same side as the screw in question. You should see the other end of the ...2Pcs Toilet Seat Screws, Steel Toilet Seat Hinge Bolts and Nuts, Heavy Duty Toilet Seat Fastener with Plastic Nuts and Metal Washers, Toilet Hardware Replacement for Top Mount Toilet Seat Hinges $5.99 $ 5 . 99Apr 20, 2020 · Step 1: Turn off the Water on the Toilet. Locate the toilet shut-off valve on the rear wall of the toilet and turn it clockwise. If you have the push/pull type of valve, pull the handle out. Flush the toilet and hold the flush handle down to remove as much water as possible. How to replace toto toilet seat with hidden bolts, 1. Locate the bolts that hold the toilet seat to the toilet bowl. These bolts are typically located on the back of the toilet seat, near the hinge. 2. Apply penetrating oil to the bolts. This will help to loosen the bolts and make them easier to turn. 3. Use an adjustable wrench to loosen the bolts., Ensure that the rubber washer is placed between the bottom of the inner tank and the bolt head. After inserting the bolts into the tank, place them in the pan and then into the toilet bowl openings. Tighten the bolts using your hands and then use a wrench to tighten them at the bottom of the toilet seat., To remove the metal screws, unscrew the nut from the bolt with a socket wrench equipped with a deep well socket. According to Family Handyman, most toilet seats with metal bolts require a 1/2-inch socket. Advertisement. Article continues below this ad. A deep socket should be able to fit over the long bolt and tightly grip the nut., Step 1: Locate the Seat Bolt Covers. Locate the two covers that hide the seat bolts at the back of the toilet seat. Each one is hinged, and you have to pry the side that's opposite the hinge to snap the cover up and expose the bolt. You may be able to do this by hand, but if not, a flat-head screwdriver can do the job., Toto Toilet Seat Removal. The following is the correct procedure to replace the Toto toilet seat: Identify and locate the seat bolt covers. Using a flat-head screwdriver, or just your hands, pry the side that is opposite the hinge to snap the cover-up and expose the bolt. Each one of the two covers hides the seat bolts at the back of the toilet ..., Scrape off any loose debris from the toilet bowl rim with a toilet brush. 3. Pour a cleaning solution onto the toilet bowl rim. 4. Let the cleaning solution sit for the amount of time specified on the label. 5. Scrape off the cleaning solution with a toilet brush. 6. Rinse the toilet bowl rim with water. 7. Dry the toilet bowl rim with a towel., Plumb Works® Plastic Replacement Toilet Seat Hinge Bolts. Model Number: PF8036-PS Menards ® SKU: 6641188. PRICE $2.99. 11% REBATE* $0.33. PRICE AFTER REBATE* $ 2 66. each. ADD TO CART., Drilling is difficult, and likely to crack the toilet. Unless you have a reverse threaded brill bit, as you try to drill into the bolts, they will try to tighten. One old way would be to try to carefully notch a slot for a regular head screwdriver bit, and then use a large breaker bar attached to a bit socket with said screwdriver bit., I too have a Toto toilet and I was having trouble accessing the bottom of 1 side and the other side was impossible to access. I was able to loosen the screws enough and use a bolt cutter to pop off the heads of the screws. The rubber then was easy to push through. I reinstalled with the new TOTO rubber Mollys and it was an easy fix., Father and daughter fix the broken plastic screws on the toilet seat lid's hinges, and replace them with metal ones.Replacement Hinge Brass Bolts, Washers an..., Put the nuts in place. Now you can unpack your new seat and fixings. Always read the manufacturer's instructions. Drop the nuts through the holes in the toilet and use the screwdriver to tighten them in place. 5. Replace the covers. Push the stainless steel covers over the brackets. 6. Finish installing the seat., Sarah Buhr speaks with Nathan Jauvtis about his company Bolt and the electric motorbikes they manufacture by hand in their San Francisco garage. Sarah Buhr speaks with Nathan Jauvt..., Learn how to identify and replace the essential parts of a Toto toilet tank with Jim's expert guidance and tips. Watch this video to fix your toilet problems., This How To Replace Inside Of Toilet Seat With Hidden Bolts will not only satisfy your needs, but it will also make you stand out from the crowd. In addition to ensuring that you receive a genuine product, we also guarantee your satisfaction by allowing you to return your product for a full refund within 30 days of purchase. We've been in ..., My daughter had a new toilet fitted last year and now the toilet seat has become loose. Not usually a problem I know, but the fixing beneath the back of the toilet is hidden by the side of the toilet which reaches almost to the wall. The fixing can just be reached by curling fingers around the the back of the toilet, but only your finger tips ..., To replace a Toto toilet seat with hidden bolts, follow these steps: 1. The first step is to locate the bolts securing the toilet seat. Depending on the model, these bolts may be hidden beneath caps or covers on the seat hinges. To access the bolts, gently pry open the caps with a screwdriver or your fingernail., So now you know this is not a simple room. Now the issue. the foyer has a blue water marks in the ceiling. I suspect its the toilet. But the toilet has no floor mount nuts/bolts or covers or anything. 2 different flooring guys couldn't match the non-slip semi-clear Ceramic tiles that cover the bathroom floor and stairs to it., Prepare the Area: Start by ensuring that the area around the toilet is clean and free from any obstructions. This will provide you with ample space to work and maneuver as you remove the toilet seat. Identify the Fasteners: Examine the underside of the toilet seat to identify the type of fasteners securing it in place., Step 1. How to Measure a Toilet Seat. If you don’t need to buy a toilet seat and you have already measured up and purchased one then you can skip this step and go straight to step 2. Before you remove the old toilet seat, check the measurements of your toilet and ensure you have the correct toilet seat to replace the old one with., A leaky toilet is always a nightmare, but sometimes, the leak may simply be fixed by replacing a few hardware. In this video, I will show you, how to replace..., TOTO SoftClose Non Slamming, Slow Close Elongated Toilet Seat and Lid, is the latest in innovative smart seat technology. Constructed of solid, High-Impact Plastic, this unique seat is specifically designed to reduce injury and to eliminate annoying "Toilet Seat Slam." The seat and lid utilize a built-in SoftClose hinge system, which lowers the ..., Feb 6, 2023 · 1. Remove the caps from the bolts. You may need a screwdriver or other tool to do this. 2. Unscrew the bolts and remove them from the toilet. 3. Lift off the old toilet seat and set it aside. 4. Place the new toilet seat on the …, Soft close toilet seats work by utilizing a special slow-close hinge system that lowers the toilet seat gently and quietly. Soft close toilet seats are available to fit either roun..., AI is not sophisticated enough to replace trained TV writers. Yet as the Writers Guild strikes, networks won't budge on demands not to use AI. In the must-watch final season of “Su..., BOETOADG 2Pcs Universal Toilet Seat Bolt and Screw Set, Heavy Duty Toilet Seat Hinge Bolts with White Plastic Nuts, Metal and Rubber Washers, Replacement Parts for Top Mount Toilet Seat Hinge. 93. 200+ bought in past month. $598. List: $6.59. FREE delivery Thu, Jan 4 on $35 of items shipped by Amazon., The real kicker is when (not if) the toilet seat needs to be replaced. This is usually a 5-10 minute job on most toilets. On this thing, it's a two-day project and will cost just under $100. You read that right! The nuts (threaded inserts, actually) are completely enclosed and inaccessible., 1. REMOVE THE OLD TOILET SEAT. Make sure to clean the surface around the mounting holes. 2. INSTALL THE WASHLET SEAT MOUNTING BRACKET. Using a Phillips-head screwdriver, tighten the screws just snug enough to allow movement so you can adjust it to align the seat. 3. SLIDE THE WASHLET ON THE BRACKET., Remove the seat and measure from the center space between the seat bolt holes to the front edge of the bowl. Round bowls should measure 16-1/2 inches, while elongated bowls should be about 18-1/2 inches. Measure the distance between the center points of the bolt holes. This distance should be 5-1/2 inches., Mar 9, 2008 · I have to buy one of the skirted Toto's since I have a 10" rough-in. My question is: how does one replace a seat cover on a skirted toilet once it's installed? The skirt covers the entire pedestal including where the seat cover bolt come through., Hibbent Universal Toilet Seats Screws and Bolts Metal - Toilet Seat Hinges Bolt Screws, Toilet Seat Fixings Expanding Rubber,Toilet Seat Replacement Parts Kit(5 Choices) 4.3 out of 5 stars 1,147 1 offer from $15.99, Proceed to the next step to reattach the toilet seat, completing the process of restoring stability and functionality to your Toto toilet. To tighten a Toto toilet seat, use a screwdriver to tighten the bolts underneath the seat. Make sure the seat is centered and then tighten the bolts evenly on both sides., Step 4. Follow this step cautiously. Take the bolt and rubber washer first. Put the washer inside the bolt and later put the bolt into the water tank. Underneath the toilet tank, first, use a metal disk or washer, and then use a nut. Now tighten the nut enough so that no water can pass through it. Cover this bolt with the gasket., The first step to removing a Toto toilet seat is identifying where the bolt is located on the bowl to prevent questions like, "How to replace a Toto toilet seat with hidden bolts." Without wasting further time, let's get started. METHOD 1 Raise the Seat Cover