Wyze camera blinking red and blue

Reset the Device. If you see your Wyze camera’s blue light blinking, it may indicate that there is a problem connection between your device and Wi-Fi network. The first thing you should try is to reset your device. To do this, simply press and hold the setup button for about 10 seconds until you hear a voice prompt saying “Ready to connect.

cam-v3. For the life of me I cant get the camera to boot into firmware flash where im supposed to get a solid purple light. I know your suppose to shut the camera off (I have a switch on my flood light in my house so I just turn the switch off) then hold the setup button while powering it back on (again i just flip my switch on) and hold it for ...Status Light Guide. Solid blue light: Headphones are powered on and connected to the Wyze app. Flashing blue: Connecting to paired device. Flashing blue and red: In pairing mode, not connected to the Wyze app. Solid red light: Headphones are connected to power and charging. Solid green light: Headphones are connected to power and 100% charged.The reset procedure doesn't work, the camera keeps going into"ready to connect" mode. When I plug it in, the light starts solid fed then changes to red/blue flashing after a few seconds. I am using a formatted 32 gig sdhc from Wyze. I'm going to try again, and hope for a better outcome.Base Station, with wireless connection, and 3 Outdoor Cams all with latest firmware updates as of 8-15-21. Worked great for several months. Now the base and all 3 cams are offline. Light on base is flashing blue. Power cycled the base and on restart got steady yellow then flashing blue light. Wired (ethernet) base to my router, same results. Removed base from app (latest version) and tried to ...Hey, I have a Wyze Cam v3 that keeps switching from red to blue. From my understanding, I know red means it's recording to the cloud or someone is watching it. No one has been on the camera recently, and it does the same even if we're not moving. It does this randomly too.Check the back LED ensuring it changes from solid blue to blinking yellow. Remove the microSD card from the slot. Press and hold the setup button at the camera’s bottom for at least 10 seconds. Wait for the ready to connect message. Once you reset the camera, proceed to repeat the setup process.Webcam Firmware Instructions. Can't connect to the Live Stream. Remote Live Stream Failure. Settings Not Updating. Alexa cannot discover or connect to the camera. IFTTT Troubleshooting. Google Assistant cannot recognize or connect to the camera. Poor Image Quality. How to flash your Wyze Cam firmware manually.To factory reset Wyze Cam Floodlight v2: Remove any microSD card inserted into the floodlight. With the floodlight powered on, press and hold the setup button on the side of the camera for 10 seconds until the status light on the front of the camera turns solid red. Once the status light starts flashing red, set up the floodlight like new.

Logread is empty. Dmesg is below. But strange thing, while waiting camera to boot with minihacks, I heard a click and solid red light changed to blinking red light. I pressed setup button and heard ready to connect prompt. Tried to connect, but it failed, saying "Cannot connect to local network". I cannot reset camera, as it goes straight to solid red light. I powercycle camera with ...Wyze Battery Cam Pro Status Lights. Solid yellow - The camera is powered on and initializing. Flashing yellow and blue - The camera is ready for pairing. Solid blue - The camera has been paired successfully. Solid red - The camera is connected and powered on, an Event is being recorded/uploaded, the user is viewing the live stream, or a log is ...Bought new Pam Cams from Amazon. Upgraded them to new firmware after setting them up. Issue: Can view the live stream while on same WiFi network but can't connect to cam or vie live stream while on cellular. The blue light also keep flashing. I'm getting sounds alerts so looks like cameras are working but not showing the live view. Can someone help?Tried factory resetting the camera multiple times and connecting it to wifi about 100 time and get the same result. Shows as everything went ok on the app and lets me name the device but the camera eventually says connection timed out please rescan QR code, and eventually changes from blinking blue to red again. UpdateIn all cases the camera results in a flashing blue led light. I also confirmed the camera is connected to my wifi network and does respond to a restart via the wyze app. I just do not receive a video stream via the wyze app. At this point I’m am confident it’s an issue with the latest firmware 4.49.11.8391 and wyze app. Hopefully they will ...Copy the demo.bin to a 2 GB SD card (the exact same steps did not work on 3 different 64 GB cards) Insert the SD card into the camera. Press and hold setup button on the camera. Plug in the power. Wait 5-10 seconds for the solid orange to change to a solid light blue (in reality just the orange and blue at the same time)After flashing, it behaves the exact same way as above: flashing red light/refuses to connect to wireless network. Flashed the initial firmware (4.36.0.125). Same as the prior two firmwares: stuck at flashing red light/refuses to connect to wireless network. Flashed latest production build again just as a sanity check: stuck at red light.

Check if there are any ongoing issues on wyze.com & the Wyze app. Monday through Friday, 6AM-6PM, Saturday & Sunday 8AM-4PM Pacific. Holiday hours may vary. Find answers, ask questions, and connect with your fellow community of Wyze users. All Wyze devices have a handy status light that helps determine what state the device is in.Theres a lot to be optimistic about in the Services sector as 3 analysts just weighed in on Vertex Energy (VTNR – Research Report), Blink Charging... According to TipRanks.com, Day...With the camera powered on, press and hold the setup button on the bottom of the camera for 10 seconds until the status light turns solid yellow. To access the setup button, you will need to open the camera's battery compartment. Once the status light starts flashing yellow and blue, set up the camera like new.Remove any microSD card inserted in the camera. With the camera plugged into power, press and hold the SETUP button on the bottom of the camera for 10 seconds until the status light on the front of the camera turns solid red. Once the status light starts flashing red, set up the camera as new. Reboot your router.Detailed Wyze Cam Floodlight v2 Status Light Guide. Status light: What does the light mean? Solid red light. The floodlight is powered on and initializing, the user is watching the live stream, or an Event is being recorded. Flashing red light. The floodlight is ready to connect to Wi-Fi. Flashing red and blue lights.

Cho troi golden west.

Keeps blinking blue: Wyze Cam V3 and Pan Cam V2. Cameras have been online and working since I bought them. However, since the major outage and security breach all my camera's (2 x Wyze Cam V3 and and 2 x Wyze Pan Cam V2) keep on blinking blue and I have trouble with accessing the video via the app on my phone (even with 5G and full bars).Factory reset the camera and then set it up as new. Remove any microSD card inserted in the camera. With the camera plugged into power, rotate the lens of the camera so it is facing up and single-press SETUP for 10 seconds until the status light on the front of the camera lens turns solid red. Once the status light starts flashing red, set …This is happening to me with RTSP firmware which is stagnant but after app update 2.48.5 and only with Pan V2. The rtsp url works just fine from any viewer, but the moment I try to use the Wyze app the blue light starts blinking and refuses to display the feed within the Wyze app. Says it is offline which is not the case as they shows up on my router's client list.According to the Quick Start guide, the status light should be Blue with operating normally. However, all four of mine are working perfectly, but the status LED is solid red. I did see the Blue LED during setup, so I know it is working in all four cameras. All four cameras are firmware version 4.36.0.228.Turned on cam today and wasn't able to connect to camera. Power cycled camera through Wyze app. Cam is stuck at blue … Tried 2 different power outlets Removed SD Card and power cycled Cam Removed Cam v2 from Wyze app. Wyze Forum Wyze Pan Cam v2 stuck at blinking blue light. Cameras. cam-pan-v2. larrybruce October 7, 2021, 4:22am 35.Add device. Select Cameras. Select Wyze Base Station. Plug in the power and network cable to the base, blue light on base is flashing. app is searching for the base but never finds it. After 2 minutes, I check the box for ‘The status light is solid blue’, next. select ‘Set up with QR code instead’. Scan QR code.

Some laser printers, including many business-oriented black and white and color units, use an imaging drum that is separate from the toner cartridge. The drum is coated with a chem...Tried factory resetting the camera multiple times and connecting it to wifi about 100 time and get the same result. Shows as everything went ok on the app and lets me name the device but the camera eventually says connection timed out please rescan QR code, and eventually changes from blinking blue to red again. UpdateFactory reset your Wyze Cam v3. Remove any microSD card inserted into the camera. With the camera plugged into power, press and hold the setup button on the bottom of the camera for 10 seconds until the status light on the front of the camera turns solid red. Once the status light starts flashing red, set up the camera and floodlight as new.Sep 5, 2023 · 2 Steps to Diagnose and Resolve Blinking Yellow and Blue Light on Wyze Cam. 2.1 Update the Firmware. 2.2 Switch to 5GHz WiFi Band. 2.3 Change the WiFi Channel on the Router. 2.4 Move Router to More Central Location. 2.5 Relocate the Camera Closer to Router. 2.6 Perform Factory Reset and Reconfigure. 2.7 Clone MAC Address.<div id="jsWarningMsg" class="warningMsg" style="display: flex; justify-content: space-between;"> <p style="color: var(--old-on-surface-high-emphasis, #22262B); font ...Aug 7, 2022 · With the Wyze Cam Pan plugged into power, press and hold the setup button on the bottom of the camera for 10 seconds. This will reset the camera. Wait at least 30 seconds for the unit to initiate. This process can take up to 5 minutes. It’s rare, but it’s possible.It turns purple (blue & red) for approx 10 seconds, then the blue light turns off and the red light stays solid for eternity. I can do it over and over, same results (I know…insanity) so it's tanked. I'll keep an eye out to see if Wyze ever addresses the issue. Meanwhile, I'll function with 9 cameras instead of 10.Troubleshooting. Make sure you are using the cord and adapter that came with your Wyze Cam. If you're able to, try switching out the cord and/or adapter to see if the camera powers on. The power cable and/or adapter may be defective. Try plugging your camera into a different power outlet. The power outlet may not have power.Oct 5, 2021 · Power cycled camera through Wyze app. Cam is stuck at blue blinking light unable to connect. Steps taken to resolve: Power cycled Cam (Left unplugged for 5min) Tried 4 different power outlets (Directly to Known good power outlet & tried with 2 known good power strips) Removed SD Card and power cycled Cam.

A solid yellow light indicates that the camera is in setup mode and ready to be connected to your Wi-Fi network. If the light is flashing blue, it means that there is an event recording in progress. Lastly, a solid red light indicates that the Wyze Cam is currently recording footage. Understanding the different status light indicators will help ...

This is the second Wyze Cam Pan for me to do this same thing. I noticed that the lights were flashing yellow/blue and the device was restarting every 30 seconds by seeing it spinning and doing the set up process. I’ve power cycled it about a hundred times and even removed it from my device list on my app. When I attempt to add it back to my …A solid blue light indicates that the Wyze Cam is properly connected to Wi-Fi and fully operational. Flashing Blue Light: A flashing blue light indicates that your camera is currently pairing or attempting to connect to your Wi-Fi network. Solid Red Light: A solid red light means that the camera is connected to your Wi-Fi but cannot access the ...Same thing here. I have 4 V2 cams and they are all blinking today. I reset them and same blinking blue. I even flashed one and still the blinking blue. The V2's are all working fine, just the irritating blinking blue.Tried factory resetting the camera multiple times and connecting it to wifi about 100 time and get the same result. Shows as everything went ok on the app and lets me name the device but the camera eventually says connection timed out please rescan QR code, and eventually changes from blinking blue to red again. UpdateThis might mean that the camera is placed too far from the Wi-Fi router, or the signal is weak. Another possible reason for red lights is when the Wyze camera is updating its firmware. During the update process, the camera will display a red light, indicating that you shouldn’t disconnect the camera or turn it off.The blue and yellow alternating blinking pattern on the Wyze camera indicates that the camera is in setup mode, which means it is ready to be set up or is currently processing a setup request. This can occur when you're setting up a new Wyze camera or when you're adding a camera to expand your existing network.With the camera plugged into power, press and hold the SETUP button on the bottom of the camera for 10 seconds until the status light on the front of the camera turns solid red. Once the status light starts flashing red, set up the camera as new. Once the camera is set back up, enable the spotlight under Spotlight Settings.Power cycle the camera by unplugging the power and plugging it back in. If the camera returns to flashing yellow but never reconnects, set the camera up as a new device. On the Hometab of the Wyze app, tap the + plus sign in the upper left, then select “Add Device” . (This can be used to re-setup a camera as well) This will initiate the ...Tap Next again, then confirm that your doorbell has a solid blue light. Tap Next. Mount the device by placing the doorbell onto the wall plate matching the holes on your doorbell. Tap Next when finished. You'll be prompted to set up your Wyze Chime. To set up your Wyze Chime: Tap Add a Wyze Chime, then tap Next to continue.

Rit dye more color chart.

Conns pay your bill.

Just make sure to have your Wi-Fi information and camera details handy. With these steps, you can remove and add your Wyze camera with ease. Check Camera Hardware. If you’re experiencing a flashing blue light on your Wyze camera, there could be a hardware issue that needs to be addressed. The first thing to check is the camera itself.They were on firmware version 4.36.2.5 and suddenly just appeared offline in the app with a solid red light. Flashing just resulted in the light being temporarily purple before turning solid red again. I tried to flash several different firmware versions. They failed within a week of each other. I chatted with Wyze and they replaced the first one.Next I decided to delete the camera from my app in hopes of resetting everything again, but now the camera is stuck in an endless loop of flashing the blue and yellow light, panning around the area, and then turning off. It turns back on again after several minutes on its own and it does the same flashing lights and pan again and turns off again.R.Good July 12, 2023, 1:30am 4. There are two blue pulsing definitions for the VDBP. For Battery powered, the device will pulse blue when you are live streaming the camera or an "event" is happening. The direct power setup will pulse blue when is standby mode as you have found.Credit cards using "contactless" technology allow you to pay for stuff by holding the card near a special reader instead of swiping it or handing it to a clerk. Find out how �bli...Flashing yellow and blue light: Camera is pairing with the Base Station. Flashing red light: Camera is plugged into power and charging. Flashing red light, quickly: Camera restart needed. Press and hold SYNC button for 10 sec to restart cam. Solid red light: Camera is plugged into power and done charging.Jul 25, 2022 · The 12 cameras connected automatically and work. but the blue light is going between solid blue for a while and fast blue flashing. I just changed my password to the APP and reset all the cameras, then re-added all the cameras, all the cameras are still flashing blue. but will go solid blue after sometime.No light? Make sure it's properly connected to power. Wyze Cam Pan v2 Status Light Guide. Solid red light - The camera is powered and starting up. Flashing red light - Ready to connect to Wi-Fi. Flashing red and blue lights - Connection is in progress. Flashing blue light - The camera is connected and finishing setup.After the router is connected to power and has booted up: Flashing white light - In pairing mode. Flashing blue light - BluetoothⓇ provisioning process. Solid white light - Successfully paired or initially powering on. Flashing orange light - Router is booting up. Rapidly flashing orange light - Factory reset via pinhole method has initiated. ….

Green blinking and red blinking explained. By Adam Juniper. ... indicating a connection issue - then it will turn blue, then blink green for a while as the connection is made to your wi-fi and then to the internet. ... Adam brings a wealth of knowledge across a vast number of product categories, including timelapse cameras, home security ...When the blue light is flashing rapidly, it means the plug is in pairing mode, ready to be connected to your Wi-Fi network. Once it connects, the blue light will turn off. If the blue light continues to flash steadily, it means the plug is disconnected from the Wi-Fi network and needs to be reset. To reset, simply unplug the device and plug it ...I have four Wyze Cam v1 cameras. Last night (5/4/22), one of them went offline. I found its status light blinking blue and performed a power off reset. It went through the boot sequence normally, but returned to a blinki…My Wyze Sense v1 has been on my door and working perfectly with the original, pre-installed battery since 2020. A few days ago, it chimed for the 1st time ever, apparently to tell me to change the battery (I didn't know it could do that). [UPDATE: the sensor proabably didnt chine. Coincidentally, the smoke detector nearby was chirping a low battery warning.] The light was flashing red. I had ...Power cycled camera through Wyze app. Cam is stuck at blue … Welcome to the community @MeekB2G! Thank you for the well detailed troubleshooting steps. ... Now the device is no longer blinking a blue light but a red light and I still cannot connect to the device in the WYZE app. Screenshot_20211005-113827_WyzeBeta 720×1520 105 KB.Flashing Red, Red and Blue, or Blue. Use the same troubleshooting steps any time the status light whenever the status light is flashing unexpectedly. If the camera returns to flashing red but never reconnects, set the camera up as a new device. In the Wyze app, tap Home then the + plus sign. Then tap Add Device > Cameras and select your camera.Blinking blue light on mine is a condition of overheating. I’ve suspended the unit at a 45 degree angle with the front pointing down and the antennae on the upper end. This has kept it cool enough for about 4 weeks of operation before it requires to be unplugged and brought down to room temperature. This base station should be a little bigger ...It turns purple (blue & red) for approx 10 seconds, then the blue light turns off and the red light stays solid for eternity. I can do it over and over, same results (I know…insanity) so it's tanked. I'll keep an eye out to see if Wyze ever addresses the issue. Meanwhile, I'll function with 9 cameras instead of 10.To do this, press and hold the setup button on the bottom of the camera for 10 seconds until the LED flashes yellow, then release the button. Finally, try updating your camera and firmware to the latest version. This can often solve connectivity issues and fix any bugs that may be causing the blue light to blink.When I entered the room, the red light on my Wyze pan scan camera was on. There is only 1 pers… The status light turns colors when it is being accessed by the app such as live streaming and when it is actively detecting motion. It was probably detecting your movement. ... But when my detect motion is disabled, my status light stays blue.on my ... Wyze camera blinking red and blue, Solid light until bootup is complete: A solid blue LED light during bootup means the camera is booting up.It will automatically go off after a successful bootup. The Stick-up camera is a bit different than the Spotlight, so here are more patterns to look out for:. Fast light blinking (blue/red): A fast blinking blue/red light means the alarm/siren …, A hardy plant with blue berries, bayberry has been used therapeutically for centuries. Some research backs up its potential. Bayberry is a hardy plant that produces waxy, dark red ..., It would be recommended to NOT reset any cameras or subscribe to any Wyze services during this time. Hopefully Wyze will make a statement about this shortly but for now just hold tight and wait. ... Woke up to 4/6 cameras blinking blue, ive restarted cams, and internet and no fix. Wyze support bot hasnt been any help. Im glad i dound this. 1 Like., To do this, follow these steps: Unplug your Wyze camera from its power source. Insert a pin or paper clip into the small hole at the base of the camera. Press and hold the reset button for a few seconds. Plug the camera back into the power source while keeping the reset button pressed., I have two cameras this happened to. I was initially able to connect the cameras to the wifi and view. After unplugging the camera to install where I want to view and reconnecting to power the cameras won't connect and I see a red and blue flashing light and the app shows the cameas as being offline. I proceeded to remove the cameras from the wifi and try to re-install them. I get all the ..., On the app, click and open the Wyze camera to which the Spotlight is connected. 2. ... Why is Wyze camera flashing? A flashing red or blue or red and blue LED indicates power issues or pairing/setup issues on the device. If you encounter such circumstances, try power cycling the device and re-configure the system from scratch. ..., in Eufy. If your Eufy camera is flashing blue light, it indicates that the camera is ready to set up. If it's flashing red, it means the camera is disconnected from the Internet. If other colors (blue and red) are flashing at the same time, it indicates that the camera needs a firmware update. The erroneous blinking lights can show up quite ..., Troubleshooting Steps. Reboot your Wyze Base Station to re-establish the connection. Unplug the base station from power, wait 5-10 seconds, then plug it back in. Once the status light is solid blue, the reboot is complete. Check the status light on the Base Station and Wyze Cam Outdoor v1/v2. They should both be solid blue., Removed base station from app. Plugged into main network switch. Held reset pin for about 15 seconds until flashing blue light stops, momentarily goes solid blue, then to yellow. Unit reset, flashed blue for about 30 seconds and then went to solid blue. Setup as new base station on app. Set camera to “new” base station. Voila! Good Luck. …, Nov 29, 2023 · If you’re seeing your Wyze Cam V3 flashing red and blue, then it’s an indicator that something’s not right. This issue is known as the “flashing status light” problem, and it can occur due to various reasons, such as an incorrect power supply, a faulty SD card, or a network issue., To perform this step, plug your Wyze cam into power and press and hold the button for 10 seconds for Cam v1 or 20 seconds for Cam v2/v3. After the process begins, it should take about 30 seconds before the LED indicator starts changing to solid red on a Cam v3 or Flashing Yellow on a Pan v2. If the status light is still solid red after the ..., In conclusion, a Wyze camera blinking blue is actually a genius display of its smartness. It's like a little brain that knows when to alert you of something important and keeps you in the loop. It blinks blue to let you know it's analyzing footage, checking for motion or sound, or performing other intelligent tasks. ..., Go to Account on the bottom and then tap Firmware Upgrade. From the Home tab of the Wyze app, tap the + plus sign in the top left. Select Add Device. Tap Sensors > Wyze Contact Sensor or Wyze Motion Sensor. On the next screen, select the camera you want to connect your sensor to. Use the included Reset Pin to poke the reset button on the sensor ..., 18 Apr 2023 ... Hold the setup button, plug in your USB cable, keep holding the setup button for 3-6 seconds until the light is solid blue, then release the ..., On Android: In the Settings app, tap General management or System, tap Reset or Reset Options > Reset Network Settings. Confirm the reset. Power cycle your Wyze Cam. Unplug your camera from the power outlet, wait 5-10 seconds, then plug it back into power. Force close the Wyze app, then open it again. How to force close an app on …, I have had this one outdoor working great, then stopped connecting. plugged in and chared til red light is solid and turned on. I get a blue blinking light and press sync and get a fast blue/yellow light, but will not connect through the app. I know have to outdoor cameras i replaced with the updated pan I cant re-use elsewhere., Wait for a solid or blinking yellow light (red for Wyze Cam v3). Wait for the reset process to be completed. It can take 5 minutes. Set up your camera on the Wyze app. Why is my Wyze camera flashing blue but not connecting? A flashing blue LED indicates that your device has already recognized the router, but the network is poor., Hold down on the setup button and don't let go for a minimum 17 seconds (I timed a V3 reset) until you actually hear the cam click and the 4 IR LED lights on each side of the lens flash. Do not let go of that Setup button until the cam does this. When it does, it should restart to a blinking red light. Unplug the Cam., 31 Jul 2023 ... This is how to turn off the blue light on Ring Cameras. Amazon affiliate link: https://amzn.to/3sh06bc -------------------------- The above ..., Any known issues with Wyze servers? All my cameras are off-line (strike through cloud icon). Everything else on my network works except my three v3s. I woke up this morning and the blue light was blinking. I disconnected them from power for over 30 seconds, powered them back on and they fail to connect. Now the light blinks red and …, After flashing, it behaves the exact same way as above: flashing red light/refuses to connect to wireless network. Flashed the initial firmware (4.36.0.125). Same as the prior two firmwares: stuck at flashing red light/refuses to connect to wireless network. Flashed latest production build again just as a sanity check: stuck at red light., It was powered down for about 4.5 hours. Went out, left it alone. Came back and attempted to re-add. Went through the normal setup process and the Camera is back online. Powered it down and moved it to it's normal spot, it came back up and is alive., 2. Then, press and hold the setup button for 15 to 30 seconds. 3. Then wait for at least 30 seconds for your cam to reset (this may take up to 5 minutes). Once the status light changes from solid yellow to blinking yellow, your device is ready to pair. Pair the Cam back to the app and check for the issue now., I decided to climb up on the ladder to try and cut power at the camera and noticed the camera was buzzing and there were four red lights on the front around the lens. Those 4 red lights are the IR lights it turns on when you are using nightvision. The other noises may be indicating that the camera is caught in some kind of rebooting cycle or it ..., Press and hold the setup button on the bottom of the unit for 10 seconds for Wyze Cam V2 and Wyze Cam Pan units and 20 seconds for Wyze Cam V1 units. Allow at least 30 seconds for the unit to initialize. In some rare instances, this process can take up to 5 minutes. The LED on the back should move from Solid Yellow to Blinking Yellow., When the colors red and blue are mixed together, violet or purple is produced. Purple is a secondary color and can only be made by mixing these two primary colors together. Red and..., Pan/Tilt/Zoom. Use the control panel in the Wyze app to pan and tilt the camera for a 360° live view. Pan Scan™. Automatically scans its surroundings by rotating to up to 4 custom waypoints. CMOS Starlight sensor. Reduces noise from low light, sees in environments up to 25x darker. Versatile mounting. Magnetic, screw, and 1/4-20 tripod mounting., Cameras. floodlight-pro, iphone-ipad. badtotheboneparanorm November 29, 2023, 11:17pm 1. Does anyone know why my Wyze Cam Floodlight started blinking Blue? I took it out of App and now I can't reinstall, all it does is Blink Blue. Power is good and circuit breaker is good. SlabSlayer November 30 ..., Wyze Video Doorbell v2 Status Light Guide. Solid Orange: The device is powered on and initializing. Flashing Orange: The device is ready for pairing. Solid Blue: The device has been paired successfully. Flashing Blue: The device is connected and powered on, and/or motion is detected. Alternating Orange / Blue: The device firmware …, Unpack your Wyze Cam Pan v2 box, removing all plastic and packing mat... If that does not work I would contact support at (206) 339-9646 between 4 am - 8 pm PT Monday through Friday, and 8am-4pm PT Saturday. Delete the Camera and Reinstall…. Cam has been online and working since release., To do this, simply unplug your router for 30 seconds and then plug it back in. Once your router has restarted, open the Wyze app and go to the Devices tab. From here, select the light that is flashing blue and tap "Repair." This will help establish a new connection between your light and your router., The same method would work with Wyze cam v1, Wyze cam v2, and Wyze cam v3. That said, here's a quick step-by-step guide on resetting your Wyze camera. Step 1: Head over to your Wyze app. Step 2: Click on the "gear" icon. Step 3: Scroll down and click the "Delete Device" option. Step 4: And finally, your device would start flashing ..., Same thing here. I have 4 V2 cams and they are all blinking today. I reset them and same blinking blue. I even flashed one and still the blinking blue. The V2's are all working fine, just the irritating blinking blue.